Red dot mount height is measured from the top of the Picatinny rail to the centre of the optic's window, and on an AR-pattern rifle there are four standard figures: 1.41 in (35.8 mm) for absolute co-witness, roughly 1.535–1.63 in (39–41.4 mm) for lower 1/3 co-witness, 1.93 in (49.0 mm) and 2.26 in (57.4 mm). The first two line the dot up with standard AR iron sights; the two taller heights give up co-witness in exchange for a more upright, heads-up shooting position.
The chart below gives every common height in inches and millimetres, the height over bore it produces on an AR-15-pattern upper, and what each one is actually for. If you want the reasoning behind co-witness itself, read red dot co-witness heights explained alongside this page.
Key takeaways
- Absolute co-witness is 1.41 in (35.8 mm) above the rail; the irons sit in the centre of the dot window.
- Lower 1/3 is not one number: Aimpoint-pattern mounts use 39 mm (1.535 in), while Holosun and SIG use 1.63 in (41.4 mm).
- 1.93 in (49.0 mm) and 2.26 in (57.4 mm) are "heads-up" heights with no iron co-witness.
- On an AR-15 upper the bore sits about 1.24 in (31.5 mm) below the rail, so a 1.93 in mount gives roughly 3.17 in (80.5 mm) height over bore.
- A magnifier must sit at the same height as the dot; most flip-to-side magnifier mounts come with spacers for 1.41 in and 1.63 in.
Red dot mount height chart
Heights are to the optical centreline above the top of a MIL-STD-1913 Picatinny rail. Height over bore assumes a standard AR-15 upper receiver, where the distance from the rail top to the bore centreline is about 1.24 in (31.5 mm), as published by KOENG's AR-15 height-over-bore reference. Rimfire AR-pattern rifles, straight-pull conversions and airsoft replicas can differ, so measure your own rifle before you rely on the last column.
| Mount height | Inches | Millimetres | Approx. height over bore (AR-15) | What it does |
|---|---|---|---|---|
| Low mount | about 1.05 in | about 26.7 mm | about 2.3 in (58 mm) | Keeps the dot close to the bore; suits bolt-actions, shotguns and rimfires rather than an AR stock |
| Absolute co-witness | 1.41 in | 35.8 mm | 2.65 in (67.3 mm) | Iron sights line up with the dot in the centre of the window |
| Lower 1/3 co-witness (39 mm) | 1.535 in | 39.0 mm | 2.78 in (70.5 mm) | Irons sit in the bottom third of the window; the Aimpoint Micro-pattern standard |
| Lower 1/3 co-witness (tall) | 1.63 in | 41.4 mm | 2.87 in (72.9 mm) | The figure Holosun and SIG use for lower 1/3 on their rifle dots and magnifier spacers |
| 1.93 in | 1.93 in | 49.0 mm | 3.17 in (80.5 mm) | Head-up posture; irons no longer co-witness |
| 2.26 in | 2.26 in | 57.4 mm | 3.50 in (88.9 mm) | Tallest common height; built for night vision, respirators and very upright shooting |
Where those figures come from: the 1.41 in and 1.535 in pair is printed on Primary Arms' GLx riser mount (1.41 in without its spacer, 1.535 in with it). Reptilia sells its Aimpoint Micro mount as "lower 1/3 (39 mm height)" with a separate 1.93 in version. Unity Tactical's FAST Micro is specified at 2.26 in to the optical centreline. Holosun ships the ARO EVO with a 1.63 in lower 1/3 mount and a 1.05 in low mount.
Why lower 1/3 has more than one number
Absolute co-witness is fixed by the geometry of AR iron sights, so almost every maker agrees on 1.41 in. Lower 1/3 is a description of where the irons appear in the window, not a single dimension, and makers have settled on different figures between about 1.535 in and 1.63 in. The difference is only 2.4 mm, and both put the irons low in the glass, but it matters in one place: a magnifier. If the dot sits at 1.63 in and the magnifier at 1.535 in, the dot will not be centred in the magnified view.
So when you buy a dot and a magnifier separately, check both figures. The Holosun HM3X, HM3X Micro and HM6X ship with spacers for 1.41 in and 1.63 in, and SIG's JULIET4 comes with 1.41 in, 1.53 in and 1.63 in spacers. Our guide to choosing a red dot magnifier covers the rest of the matching.
What height do popular rifle dots come at?
Many rifle dots arrive already on a mount, which decides the height for you:
- The Holosun HS510C has an integrated quick-detach mount with a 1.41 in dot height, so it co-witnesses absolutely.
- The Holosun AEMS CORE X2 comes on a 1.63 in lower 1/3 mount.
- The Holosun ARO EVO includes both a 1.63 in lower 1/3 mount and a 1.05 in low mount.
- The SIG ROMEO5 Gen II Elite we stock comes with a 1.41 in absolute co-witness mount.
- EOTech's XPS models sit at absolute co-witness height, while the EXPS3 uses a base raised by 7 mm for lower 1/3 co-witness, according to EOTech.
Why go taller: 1.93 in and 2.26 in
Taller mounts let you keep your head more upright, which many shooters find faster and less tiring, especially when shooting standing or with a helmet or ear defenders that push the head up. Unity Tactical describes its 2.26 in mount as giving an "ergonomically correct heads-up posture" and easier dot pickup under night vision and protective equipment.
The costs are real. You lose iron sight co-witness, the cheek weld on a standard AR stock becomes a chin weld, and the extra height over bore makes the close-range offset bigger. At 10 m (11 yd) a 2.26 in mount puts the bullet roughly 7 cm (2.8 in) below the dot, against about 5 cm (2 in) at absolute height. It also changes where your zero crosses the line of sight again; the red dot zero distance chart shows by how much.
Expert tip
Measure before you buy. Put the rifle on a bench, hold a ruler against the rail and look at where your eye naturally sits when your cheek is on the stock. If your eye is well above the 1.41 in line, a lower 1/3 or 1.93 in height will feel more natural than forcing your face down onto the comb.
UK note
Self-loading centrefire rifles are prohibited in England, Wales and Scotland under section 5(1)(ab) of the Firearms Act 1968, with an exception for guns chambered for .22 rimfire. So British AR-pattern rifles are mostly straight-pull centrefires, .22 rimfire self-loaders and airsoft replicas. The rail and the heights are the same, but rimfire and airsoft uppers do not always share the AR-15's 1.24 in rail-to-bore figure, so check your own height over bore before using a zero chart.
Choosing a height
- You want your irons usable through the glass: absolute (1.41 in) or lower 1/3.
- You want a cleaner view with backup irons: lower 1/3, the most common all-round AR choice.
- You shoot standing with your head upright, or wear bulky ear defenders: 1.93 in.
- You run night vision or want the tallest position: 2.26 in.
- The optic is on a bolt-action, shotgun or rimfire with a low comb: a low mount around 1.05 in, or a dedicated low base.
We stock sights that ship with their own mounts, and Trijicon RMR mounts for Picatinny rails and ACOGs. We do not currently stock standalone AR riser mounts in 1.93 in or 2.26 in heights, so if you need one of those, you will have to buy it elsewhere.
Frequently asked questions
What does 1.93 mean on a red dot mount?
It is the height from the top of the rail to the centre of the optic: 1.93 in, or 49.0 mm. It is taller than both co-witness heights, so your iron sights will sit below the window rather than in it.
Is lower 1/3 1.535 or 1.63 inches?
Both are sold as lower 1/3. Aimpoint Micro-pattern mounts use 39 mm (1.535 in), and Holosun and SIG use 1.63 in (41.4 mm). Match your magnifier to whichever your dot uses.
Can I use a magnifier with a 1.93 in or 2.26 in mount?
Yes, but the magnifier also has to be at that height. Most flip-to-side magnifiers come with spacers for 1.41 in and 1.63 in only, so a taller setup needs a matching tall magnifier mount.
Do these heights apply to a straight-pull or rimfire AR?
The rail-to-optic heights are the same on any Picatinny rail. What can change is the rail-to-bore distance, which affects your zero and close-range offset, so measure your own rifle.
Shop this guide
- Rifle Dot Sights — many come with a co-witness mount in the box
- Red Dot Sight Magnifiers — flip-to-side magnifiers with height spacers
- Red Dot & Magnifier Combos — dot and magnifier already matched for height
- Red Dot Sight Mounts — Trijicon RMR mounts for Picatinny rails


